The Fixit renovation technique, including the use of a 30mm thick plaster layer of Fixit 222 Insulating Plaster, created a novel room climate based on its water-vapour permeability. The combined layers of the plaster system absorb excess humidity from the air and return it in a controlled way to the
Aerogel indoor insulation, since the façades were to remain unaltered. The entire interior façade, approx. 180 m², was insulated with 5 cm of Fixit 222 then positive coated with 1.5 mm Fixit 777 Structured Plaster
The façade of this building in Zuoz, which is classified as worthy of preservation, was energetically renovated with 7 - 8 cm Fixit 222 Airgel high-performance insulating plaster. Fixit 203 was applied as the finishing plaster and painted with Fixit 784. The outer wall against the stable was insulat
A former manor house from the 17th century in Gampelen BE has been renovated for energy efficiency using Fixit 222 high-performance aerogel insulation plaster. Thanks to this, the historical appearance of today's old people's home could be preserved, the consumption of heating energy has been reduce
Rubble masonry building
Building with concrete block support, rendered with lime-based plaster
Hausmanian building, renovation of the inner courtyard, thickness of the Fixit 222 insulating plaster 8 cm.
Renovation of the building with a 30 – 60 mm thick layer of Fixit 222 Aerogel High Performance Insulating Plaster. Fixit 203 mineral-based finish coat followed by water-vapour permeable, hydrophobic, mineral-based Fixit 784 Silicate plaster roll-on paint.
Building with stone/block support Street facade application of insulating plaster Fixit 222 in 50 mm thickness.
A building group consisting of 23 elements - each with an individual fresco: a unique open-air museum.
The late Gothic building presumably served as a chaplaincy for the foundation of the Bullingerpfründe in 1460 and became a helper's house after its re-catholicisation in 1531. The approximately 500-year-old property, which is now a historic monument, has been renovated time and again over the course
All of the old plaster was stripped down to the brick and rebuilt with the airgel insulation system. The facade renovation was carried out with 4 cm Fixit 222 Airgel high-performance insulation plaster system and the mineral finishing plaster Fixit 777 2.0mm pos., was painted twice with the colored
The protected building, dating from the early 19th century, was once used as a bakery. The building was converted to a multiple-family dwelling with painstaking attention given to maintaining the historical substance. Fixit 288 Calce Clima Thermo was applied to the façade to meet the requirements of
The old base and finish layers were chiseled off and then replaced with Fixit 211, Fixit 222 Aerogel High Performance Insulating Plaster, Fixit 497, Fixit 223, Fixit 475, Fixit 777 and a paint coat. Wall base areas sealed with Fixit 373 Multiflex.
The venerable vintner's house was restored in a gentle fashion. The façade and roof structure were renovated in accordance with current techniques.
First the old base layer was chiseled off, then the surface renovated with Fixit 222 Aerogel High Performance Insulating Plaster.
Renovation of a single-family dwelling. Base and finish coats removed. Reconstruction with Fixit 211 rough cast mortar, Fixit 222 Aerogel High Performance Insulating Plaster 40mm, Fixit 493 Mineral-based undercoat stabilizer, mesh embedding in Fixit 223, undercoat Fixit 730 silicate plaster 3-4 mm.
The Chesa Palmira was built in 1672, and the original floor plan has remained unchanged till today. The façade of this historic building was energy efficiently renovated by applying an 8 cm thick layer of Fixit 222 Aerogel High Performance Insulating Plaster. Fixit 208 was used for the final coat. F
The old façade base coat was removed down to the quarry-stone wall, then completely rebuilt as follows (including allowing for appropriate drying times): Fixit 493 Mineral-based Undercoat Stabilizer was first sprayed onto the quarry-stone wall, then a 6 – 8 cm thick layer of Fixit 222 High Performan
Façade renovation with Fixit 222 Aerogel High Performance Insulating Plaster. Existing base layer removed, masonry dry cleaned and the entire façade fixed with a tile rabitz. 3 – 5 cm of Fixit 222 was applied directly onto the tile rabitz. Then Fixit 733/734 Stucco final coat was applied and two lay
The school building dating from 1884 was comprehensively renovated. Energy efficient repair of the façade using Fixit 222 Aerogel High Performance Insulating Plaster.
The façade was renovated with a 50mm thick layer of Fixit 222 Aerogel High Performance Insulating Plaster.
Increasing the thermal insulation value of the outdoor walls (due to the excessive heat loss). All exterior walls were therefore coated on their inner sides with thermally insulating plaster.
Renewal of insulation in the West Wing living area. The old base coating on all walls was removed. 4-6 cm of Fixit 688 Insulating Plaster was applied to the outdoor walls and reveals as new base coat , and 1.5 to 2.5 cm of Fixit 606 limestone-cement base coat was applied to the stairways as new base
Since no significant changes to the appearance of the façade were permitted, the decision was made to use Fixit 222 Aerogel High Performance Insulating Plaster.
The ABZ cooperative apartment buildings on Hochstrasse in Zurich Fluntern, built by Otto Streicher in 1926, were last extensively renovated in the mid-1970s. The aim was to preserve the external appearance and the internal spatial structure in their essence. Therefore, it was decided to apply an aer
Improving the energy efficiency of the entire building. Renewal of approx. 100 m2 of indoor plasterwork over 3 floors, layer thickness 3-4 cm of Fixit 222 Aerogel High Performance Insulating Plaster.
A multiple-family dwelling located in the centre of Rümland. Part of the façade was insulated with Flumroc Compact Pro mineral-wool panels, the rest (for reasons of space) with Fixit 222 Aerogel High Performance Insulating Plaster. The old base and finish layers were removed in advance of the applic
Renovation of external façade: existing base and finish coats removed. Reconstruction with Fixit 211 rough cast mortar, Fixit 222 Aerogel High Performance Insulating Plaster, mesh embedding in Fixit 223, Fixit 493 Mineral-based undercoat stabilizer, finish coat Fixit 763 white lime masonry mortar wi
Architecturally and aesthetically valuable exposed concrete walls were energy efficiently renovated by applying layer of Fixit 222 Aerogel High Performance Insulating Plaster to the indoor faces. The appearance was maintained unchanged. The excellent thermal insulation meant that a minimal applicat
The façade of this multi-family residential building was renovated using Fixit 222 Aerogel High Performance Thermally Insulating Plaster, among other materials. A 4 cm layer was applied over 1,200 m².
To achieve this thermal optimization, we first of all removed the plaster on the indoor walls then applied a 30mm layer of Fixit 222 Aerogel High Performance Insulating Plaster.
Tastefully renovated mansion house. The façade insulation was improved with insulating render. The result of the restoration work on this exceptional building was in perfect harmony with the wish to create a haven of peace.
Chateau built in the 18th century.
Since the historic building is covered by a preservation order, it was not possible to use mineral-wool insulation on its outdoor surfaces. The owners wished to retain the original character of the building, for which reason they decided that Fixit 222 High Performance Insulating Render should be us
The old mill, which was converted to a multiple family dwelling, was one of the first historically important buildings to undergo energy-efficient renovation using Fixit 222, a worldwide first. Subsequently Fixit 203 Finish Coat with hydraulic lime was applied to the façade of the protected building
Renovation of the outdoor features of an old patrician house. Fixit 670 roughcast with Armanet over the entire area, 3cm layer of Fixit 222 Aerogel High Performance Insulating Plaster, Fixit 223 mesh embedding and then Fixit 203 final coat. PIR panels used for base cladding.